รหัสสินค้า | A10s Plus | การปรับปรุงการแสดงผล | Individual Gamma adjustment for RGB : Working with the independent controller that support this feature and NovaLCT(V5.2.0), A10s Plus supports adjustment of red Gamma, green Gamma and blue Gamma, which can effectively control image non-uniformity under low grayscale and white balance offset, allowing a for more realistic image. Precise grayscale correction : Working with Precise Grayscale Tool and NovaLCT, A10s Plus supports further correction of the calibrated display, which can control the grayscale precisely. This feature can also assist other display technologies, such as 18Bit+, ClearView and individual Gamma adjustment for RGB, allowing the screen to display a more realistic image. HDR function : Supports HDR10 and HLG video sources. A10s Plus can work with the large loading capacity MCTRL4K independent controller to support HDR10 and HLG video inputs, allowing for a higher dynamic brightness range, larger color space, a smoother and more realistic image. Low latency : A10s Plus can reduce the frame latency of the video source on the receiving card end to one frame (only when using modules with driver IC with built-in RAM). 18Bit+ : Activation of 18Bit+ mode in NovaLCT can improve LED display grayscale by 4 times, avoiding grayscale loss due to low brightness and allowing for a finer image. ClearView : Enable ClearView in NovaLCT to make texture, size, and contrast adjustments on different areas of the display based on the Human Visual System, creating a more realistic image. Display rotation at any angle : When using A10s Plus with MCTRL R5, configure the display image in SmartLCT to rotate at any angle and present a variety of images. Pixel level brightness and chroma calibration : Working with NovaLCT and NovaCLB, A10s Plus supports brightness and chroma calibration on each pixel. increments (calibration not supported after rotation) : In NovaLCT, the image on the screen can be set to rotate in multiples of 90° (90°, 180°, 270° and 360°). Quick seam correction : Working with NovaLCT, A10s Plus supports quick adjustment of bright and dark lines, which can remove the seams between modules or cabinets. 3D function : In NovaLCT or operation panel of controllers which support 3D function, you can enable 3D function and set 3D parameters to allow LED screen to display 3D effects. |
ปรับปรุง การบำรุงรักษา | Supports smart module (supported by dedicated firmware program). : The smart module is composed of Flash and MCU. Flash can store calibration coefficients and module information. MCU can communicate with the receiving card to monitor temperature, voltage and ribbon cable communication status for the module. Working with the driver chip, MCU also supports open circuit detection of LED. The smart module allows for a smaller monitoring unit, requiring no independent monitoring card and saving cabinet space. LVDS transmission (supported by dedicated firmware program) : Low-voltage differential signaling (LVDS) transmission is used, which reduces the number of data cables that connect the HUB board to the module, increases the transmission distance, improves the signal transmission quality and electromagnetic compatibility, and better stabilizes the image output. Auto module calibration : After the module has been replaced and power is supplied, the receiving card can automatically read the new module ID and calibration coefficients, and save them to the receiving card. Mapping function : After enabling the Mapping function in NovaLCT, target cabinet will display the receiving card number and Ethernet port information, allowing user to view the receiving card’s location and wiring route. Setting of pre-stored image on receiving card. : In NovaLCT, a specified image can be set as the LED screen startup image or as the image to be displayed on LED screen when the Ethernet cable is disconnected or no video source signal is available. Module Flash Management : In NovaLCT, the information stored in module Flash can be managed. Voltage and temperature monitoring of receiving card : The voltage and temperature of the receiving card can be monitored without using peripherals. The monitoring data can be checked in NovaLCT. Cabinet LCD Supports NovaStar's general 5-pin LCD module. The LCD module is connected to the HUB board to display temperature, voltage, single operating time and total operating time of the receiving card. Works with NovaLCT (V5.2.0 and later) to support cabinet LCD backlight control. Works with NovaLCT (V5.2.0 and later) to support LCD run time resetting. One-click application of calibration coefficients saved in module Flash : In the event of network outage, hold down the selftest button to read the calibration coefficients in module Flash back to the receiving card. |
การปรับปรุงของฮาร์ดแวร์ | Dual-card backup : In an environment with requirements for high reliability, two receiving cards can be mounted onto a single HUB board. In the case that main receiving card fails, the standby card will serve to ensure uninterrupted operation of the display. Status detection of dual power supplies : Two power supplies can be simultaneously connected. Operating status of power supplies can be detected. Loop backup : HUB’s Ethernet port improves the reliability for the serial connection of the receiving card through main and backup redundant mechanism. If either main or backup serial connection lines fail, the other will begin to work to ensure normal operation of the display. |
การปรับปรุงซอฟต์แวร์ | Bit error detection : Working with NovaLCT (V5.2.0 and later), A10s Plus can monitor the Gigabit Ethernet communication quality between sending device and receiving card, or between receiving cards. The number of errors can be recorded to help troubleshoot network communication problems. Readback of firmware version : In NovaLCT, the firmware versions of the receiving card can be read back. Dual-backup of calibration coefficients : Calibration coefficients can be saved to both the factory partition and application partition at the same time. Calibration coefficients in the factory partition are factory values and cannot be modified by users. Calibration coefficients configured by users can be saved in the application partition and can be restored to the factory values by users. Backup and readback of the receiving card configuration file In NovaLCT, the receiving card configuration parameters can be backed up to the receiving card. In NovaLCT, the receiving card configuration parameters can be read back. |
โหลดข้อมูลสูงสุด | 512×512 pixels |
แรงดันไฟฟ้าเข้า | DC 3.3 V–5.5 V | พิกัดกระแสของมอเตอร์ดีซี | 0.5 A |
ความเข้มของการส่องสว่าง | 2.5 W | อุณหภูมิในการทำงาน | -20°C–70°C |
อุณหภูมิใช้งานปกติ | -25°C–125°C | ความชื้นในการทำงาน | 10% RH–90% RH, non-condensing |
ขนาด | 80.0 mm × 45.0 mm ×7.3 mm | น้ำหนักสุทธิ | 22.3 g |
มาตราฐานการรับรอง | RoHS EMC Class B | การบรรจุ | An antistatic bag and anti-collision foam are provided for each receiving card. Dimensions of the packing box: 378 mm × 190 mm × 120 mm. Each box contains 40 receiving cards. |